How to Hang a Redwoods Flag Indoors Without Wall Damage
By Hand-Made Surf Flags | Slightly Choppy Artifacts | Published: 2026-11-01
Category: How-to Guides
Learn how to hang a Redwoods flag indoors without nails or wall damage. Step-by-step removable flag hanging methods and display ideas for a canvas wall flag.
Quick answer
Hang your Redwoods flag with a removable adhesive strip system rated for the flag's weight, or use a tension rod inside a window frame or alcove. Both methods avoid nails and let you remove the flag without filling holes.
Why canvas flags need a different hanging approach
The Redwoods Flag is made from army-colored canvas, which is heavier and less flexible than a thin printed pennant. That weight matters: a removable hook that holds a lightweight fabric flag may creep or release under a canvas flag over time. Check the adhesive strip's rated weight and add a safety margin rather than matching the flag's weight exactly.
Canvas also has little give at the top edge. If you stretch it tight between two hooks, the fabric can pull at the corners and hang unevenly. Leave a little slack so the flag falls naturally.
When a tension rod is the better choice
A tension rod works well in a window recess, a doorway, or between two bookcase sides, because it needs no adhesive at all. It is the safer option on painted plaster, wallpaper, or textured walls where adhesive strips may not bond reliably. The trade-off is placement: you need two parallel surfaces close enough for the rod to span. If your only open wall is flat drywall, stick with removable adhesive hooks.
Placement and light considerations
Keep the flag out of direct, prolonged sunlight if you want the canvas and screened typography to stay even in tone. A north-facing wall or a spot away from a bright window is a practical choice. Also avoid hanging it directly above a heater, radiator, or fireplace, where rising heat can dry and stiffen canvas.
Step-by-step: hang your Redwoods flag without nails
- Weigh the flag and choose a removable system: Use a kitchen scale or the shipping weight to find the flag's weight, then select adhesive strips or hooks rated for at least twice that weight. Common mistake: buying strips rated for exactly the flag's weight, which leaves no margin for canvas pull or humidity. Write the weight and strip rating on your phone before you shop.
- Clean and dry the wall surface: Wipe the mounting area with a damp cloth and let it dry completely. Skip this on freshly painted walls for at least a week so the paint can cure. Common mistake: mounting on dusty, oily, or textured surfaces where adhesive cannot grip. Test a small strip in an inconspicuous spot first if the wall is wallpaper or fresh paint.
- Mark hook positions with the flag in place: Hold the flag against the wall, level the top edge, and mark both hanging points lightly with a pencil. Common mistake: measuring only one side and discovering the flag hangs crooked. Use a spirit level or a level app to confirm both marks are even.
- Apply adhesive hooks and press firmly: Press each hook firmly for 30 seconds and wait the full time recommended on the packaging before hanging anything. Common mistake: hanging the flag immediately, which prevents the adhesive from reaching full strength. Set a timer so you do not rush this step.
- Hang the flag with slight slack: Attach the flag at both points and let it settle. Leave a little slack across the top so the canvas falls naturally instead of pulling tight. Common mistake: stretching the flag taut, which can distort the top edge over time. Step back and check that the stitched details face outward and the flag hangs evenly.
- Remove slowly when you redecorate: To take the flag down, hold the wall near the hook and pull the release tab slowly downward, never outward. Common mistake: ripping the strip off quickly, which can lift paint or drywall paper. If a strip resists, warm it gently with a hair dryer on low before pulling.
Product facts
- Redwoods Flag: Hand-made flag uses army-colored canvas with off-white screened typography and stitched National Park details. The stitched details and screened lettering are part of the front face, so plan your hanging method to keep that side visible and avoid clamping hardware over the design.
Redwoods Flag
